ASTM G65 PDF

One of the more common American Society for Testing and Materials (ASTM) tests to evaluate abrasive wear resistance is the ASTM G Standard Test. The ASTM G wear resistance test is one of the more common low-stress abrasion standardized tests [1]. The consumable list consists of. The ASTM G65 test was modified in this work to reflect more accurately the actual mining conditions in an oil sands operation and create the.

Author: Shacage Turn
Country: Norway
Language: English (Spanish)
Genre: Software
Published (Last): 8 September 2009
Pages: 10
PDF File Size: 4.61 Mb
ePub File Size: 6.31 Mb
ISBN: 262-6-76393-738-9
Downloads: 31753
Price: Free* [*Free Regsitration Required]
Uploader: Nezuru

Materials of higher abrasion resistance will have a lower volume loss. It is particularly useful in ranking materials of medium to extreme abrasion resistance.

This standard does not purport to address the safety concerns, if any, associated with its use. Sample preparation equipment in Kondex metallurgical lab. It is the intent of atm test method to produce data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions.

Grinding with a surface grinder can be a controlled form of low stress abrasion. The value of the practice lies in predicting the relative ranking of various materials of construction in an abrasive astn.

Friction wheel test ASTM G65-16 (dry sand/rubber wheel test)

In order to attain uniformity among laboratories, it is the intent of this test method to require that volume loss due to abrasion be reported only in the metric system as cubic millimetres. Procedure B should be used when the volume—loss values developed by Procedure A exceeds mm 3. The ASTM G65 test simulates sliding abrasion conditions under moderate pressure, using dry sand metered between a rubber wheel and a block coupon of the material being evaluated.

All services are provided at no cost to our customers. Surfaces subjected to low stress abrasion show that material has been removed by hard, sharp particles or other hard, sharp surfaces plowing material out in the furrows.

Test Conditions Tested for revolutions at a load of 30 lb. The wear rate is significantly reduced by hard micro constituents within the surface microstructure embedded carbides for example.

  FALLING FOR YOU JEN733 PDF

This testing also saves customers considerable time and money in field axtm, allowing them to focus their efforts on the most promising products. Low-Stress Abrasion Abrasive wear occurs when hard particles are compressed with normal pressure against the surface of a metal, causing material removal. These metallurgists provide quality control, design, and analysis services, as well as research on new materials, heat treatments, coatings, and manufacturing processes that keep Kondex and our customers up-to-date on industry trends and new technologies.

Active view current version of standard. Click here to increase the life of your mud rotors. It may be used for highly abrasive resistant materials but is particularly useful in the ranking of medium- and low-abrasive-resistant materials.

Kondex employs three metallurgists with different industry backgrounds and experience levels. Volume loss data obtained from test materials whose lives are unknown in a specific abrasive environment may, however, be compared with test data obtained from a material whose life is known in the same environment.

Materials of higher abrasion resistance will have a lower volume loss. The comparison will ashm a general indication of the worth of the unknown materials if abrasion is the predominant factor causing deterioration of the materials.

Link to Active This link will always route to the current Active version of the standard. Its value lies in predicting the ranking of materials in a similar relative order of qstm as would occur in an abrasive environment.

At Your Service

In addition to daily production quality control, these competencies are also used in the design and quoting of new parts to ensure the right materials and properties are specified for each application. Link to Active This link will always route to the current Active version of the standard. The operating forces must be low enough to prevent crushing the abradant. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  COMPUESTOS HETEROCICLICOS DE IMPORTANCIA BIOLOGICA PDF

At Your Service

It may be used for highly abrasive resistant materials but is particularly useful in the ranking of medium- and low-abrasive-resistant materials. In this practice these conditions are standardized to develop a uniform condition of wear which has been referred to as scratching abrasion 1 and 3. The test allows comparison of wear-resistant materials by their volume loss in cubic millimeters, with materials of higher wear resistance showing lower astn loss.

Low stress abrasion rates are directly proportional to the sliding distance and the load on the particles or protuberances. Abrasive Wear Test ASTM G65 Surfaces subjected to low stress abrasion show that material has been removed by hard, sharp particles or other hard, sharp surfaces plowing material out in the furrows.

ASTM G65 – 04 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Procedure B should be used when the volume-loss values developed asgm Procedure Asgm exceeds mm 3.

It is particularly useful in ranking materials of medium to extreme aastm resistance. Hardness testing equipment, microscopes and digital imaging at Kondex. This machine enables us to compare materials, heat treatments, and coatings for wear resistance, a major concern for our customers. Since the practice does not attempt to duplicate all of the process conditions abrasive size, shape, pressure, impact, or corrosive elementsit should not be used to predict the exact resistance of a given material in a specific environment.

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.