ARCMATE 100I PDF

CNC Manual/Fanuc Robotics/Fanuc Robot ARC Mate i MODEL B Maintenance Manual M-6i. Fanuc Robot ARC Mate i MODEL B Maintenance Manual. Refurbished Fanuc M-6i / Arcmate i with RJ2 control and pendant. Recommended applications: Material Handling, Press tending, CNC machine tending. Fanuc Arcmate i robots with RJ3 Control, Welding robots Comes Tested Available in Large Quantities All Of Our Robots Are Tested and in A Condition.

Author: Gorn Gadal
Country: Mayotte
Language: English (Spanish)
Genre: Music
Published (Last): 3 February 2016
Pages: 177
PDF File Size: 18.90 Mb
ePub File Size: 1.14 Mb
ISBN: 906-1-30101-608-2
Downloads: 5440
Price: Free* [*Free Regsitration Required]
Uploader: Moshura

I have a laptop with RS 9pin on the back. I guess if I understand correctly, Kfloppy is listening for serial protocol and will avoid the need for any other software or hardware other then the fabricated cable.

Kfloppy is an included program that does not require a license, so it will continue to work after the trial period. December 24, I’m still hunting for a copy of Kfloppy so I can simplify the whole matter and get my two old RJs backed up. arcmwte

Fanuc Robot ARC Mate i MODEL B Maintenance Manual M-6i pdf – CNC Manual

Any insight on Fanuc programming is welcome. The question was posted last week. I haven’t been able to pull it off.

Here is where I am struggling, I can use the program shift utility to move the relevant sections of the program manually but I would like to do it from within the program. I will do the same. And welcome to arcmare forum! If you make any headway, please share the details.

The serial port is a serial port, your network interface is a network interface. It’s not just a matter of getting the signal to a network point of communication.

His Join date was Started by zaneta30 on Fanuc Robot Forum. I’m trying to setup a connection via the serial rs port with a pc and it just dont seem to work. I am using a Fanuce Arcmate i with an Rj2 controller to weld ends on to long aluminium extrusions. Fanuc Arcmate i progamming question. Thanks again for the help from forum members!

  GV2ME10 TELEMECANIQUE PDF

If I used fixed stations I end up clamping and unclamping the part six or arccmate times depending on access. It comes with Kfloppy.

Fanuc M6i / Arcmate i RJ2 in Greenville, PA, USA

It cannot be reconfigured to listen to the serial port. I was of the understanding that the STE Bridge software would create this connection, which could then be picked up on arcmqte network – or better yet, on the server laptop itself.

The left left corner tells when the question was posted. I found my old desktop with WinXP on it, and a serial port on the back. I have now copied and pasted the program so that 10i runs 4 times in one program, there is a pause programmed in for me to turn the fixture and mount the next part.

Adcmate starts and moves to a point position register near the corner of the work piece. I would like to put some steps in the beginning of the program to check and adjust the programmed positions.

Fanuc M6i / Arcmate 100i RJ2

The extrusions are on a rotating fixture so that all the welds can be done. This will not work. Advertisement Guest Advertisement Guest. I do not yet have access to the CRC. I am also still seeking the Kfloppy software so I might try to just use the older, simple method of backing them up.

Each time I sent a packet, the laptop “server” would show 16 bytes sent, and the desktop “client” would show 16 bytes received. Perhaps someone will chime in. To my knowledge, the Fanuc controller does not support this, so regardless of what you do on your laptop you cannot use the program you mentioned and expect it to work.

  CALVACHE SOLUCIONARIO PDF

This works well the only headache is adjustments to the program need to be arvmate in 4 places. The same software setup on my desktop allowed me to set it up as a “Client” to not only receive the signal via TCP, but then should make it accessible over the network – where the ERBU software will be looking for it.

Aarcmate controller – has RSC 25pin on front. I’m rather surprised your it guy didn’t know this.

I think I understand arcmaet problem you are talking about though. I move the tip to the corner of the work piece using the pendant and save that point as a second position register.

Do you have access to the Arxmate CRC? Started by latendal on Fanuc Robot Forum. The upper right tells the join date.

Started by Dave on Used Robots and parts. November 05, Hi guys, i’m having some problem with a r-j2 controller, it might be simple for some of you guys here but i’m kind of lost right now, i’ve been messing with it for a couple days so far and nothing seem to be working. My success was as far as actually seeing packets of info get transferred when I would try to backup TP 1100i from the arcmage pendant. December 31, Thanks again for the input!

In theory you can run any protocol over a serial port, but both sides need to do this, you cannot unilaterally decide to treat your serial port as a network device. I am registered with Fanuc but waiting to hear back from them.